As an entry sole cleaning equipment, sole cleaning machine aims to solve the problem of dirt brought into the room by the sole. Through the automatic induction start of the sole cleaner, the wet crawler brush rotates and rubs the sole, so as to clean up the dust on the sole, block the dust at the entrance, reduce the indoor floor cleaning workload, and establish a barrier to maintain the cleanliness of the indoor environment.
Whether you are an individual, a small enterprise, a medium-sized enterprise, a large enterprise or a listed group company, please strictly abide by the key points of installation when putting into use and installation to avoid unnecessary troubles. This is not only the responsibility of both parties, but also the respect for the results of labor.
①、make sure that the equipment is placed horizontally without shaking and tilting. If it is not horizontal, it can be changed by adjusting the movable feet.
②、make sure that the socket is grounded and the voltage is 110V or 220V. If the voltage is low, the equipment will not operate normally.
③、make sure that the water inlet and drain pipes and power lines are smooth without any buckling.
④、Please ensure that the water pressure of each drain pipe of each unit is at least 0.5MPa
According to the feedback of customers' use in recent years and our continuous inspection and understanding, the situation is relatively concentrated and summarized. As a reference for all customers, many of them are not problems at all, but problems caused by improper operation or negligence.
1、 Equipment does not work or trips
①、Check whether the power supply is turned on and whether the leakage protection plug switch is turned on
②、Check whether the power cord is broken
③、Check whether the voltage can meet the requirements
④、Check whether the sensor port is plugged in properly
⑤、check whether the sensor will flash red light. Normally, it does not flash after a few seconds
⑥、Check whether the control box lights up. Normally, No. 6 light is on (manual mode) or No. 5 light is on. No. 3 light will also be on when the water shortage alarm is turned on, and other lights will not be on
⑦、Check whether the chain is broken
⑧、Check whether there is any foreign matter blocking the chain or roller
2、 Abnormal noise of equipment
①、 Check whether the chain and gear are in good condition, and add lubricating oil irregularly
② 、Check whether the bearings at both ends of the driving shaft and driven shaft are in good condition
③ Check whether deani is loose
④ 、If the water pump makes abnormal noise, disassemble the water pump to check whether there is iron sand inside
3、 Water inlet and drainage of equipment
①、if the equipment is not drained, the cause of the failure can be found out through the following points: check whether the drain pipe is straightened out and free of pressure break; check whether the whole line of the water pump is intact and all ports are plugged in; check whether the water pump is damaged in response; check whether the drain button is damaged in manual mode
②、the blowdown water pump has been working, and the cause of the fault can be found out through the following points: check whether the controller is filled with water, check whether the drainage button is short circuited in water
③、if there is no water in the equipment, the cause of the fault can be found out through the following points: check whether there is water supply in the water pipe, check whether the water level sensor lights up and water enters, and check whether the water inlet solenoid valve acts
During the use of cleaning equipment, customers should do a good job in daily maintenance to avoid problems and the consequences of shortening the service life of the equipment, which will affect the value creation of the equipment.
Daily cleaning and maintenance
① For outdoor shoes, please clean the garbage and sediment in the sewage tank and water pump tank once a day. It is better to suck the sediment out through the vacuum cleaner. For shoes changing, you can clean them thoroughly every other day. The belt brush can be cleaned by interval, and it can be washed by hand-held water pouring into the brush
② 3 months, please add lubricating oil to the chain gear
③ . clean the equipment surface irregularly
④ Clean and update the absorbent pad according to its own use
In the process of daily use and operation, it is forbidden to allow water into the control box, or sharp solids such as nails, blades and electronic components to be mixed in the equipment cleaning area.